36000 BTU Mini Ductless Split Air Conditioner. 18000 BTU Ductless Mini Split A/C. 20 SEER Inverter System w/ Heat Pump. Enjoy full season comfort during the summer or winter with this 1.5 TON Inverter Mini Split with 18000 BTU HyperHeat Pump. With a 20 SEER coupled with DC Inverter technology this system provides the benefits of low operation temperatures, rapid cooling / heating as well as maximum energy efficient operation.
20 SEER - 10.3 HSPF4 / INVERTER DC. Indoor Unit - Air Handler. Digital Multi-function LCD Remote Control. 15ft Installation Kit (lineset + Wire).Maximum Efficiency: 20 SEER DC Inverter Technology. Pre-Charged with Eco-friendly R-410a Refrigerant.
Most Powerful Single Zone Output on the Market! 18000 BTU's of Turbo Cooling and Heating. 15ft Copper Lineset + Electrical Wire Harness. Low ambient Cooling and Heating down to -22 F.
Vertical Swing distributes air evenly throughout space. Sleep Mode - 24 hour ON/OFF Timer - Memories. Auto & 3-Speed Fan Control with 24 Hour Timer.Dimensions (W x D x H). 15 Feet Refrigeration Copper Tubing. Drain Tube for Indoor Unit. Lineset for a 25 ft. DC Inverter Air Conditioners are the ultimate cooling and heating technology of the HVAC field. They are called "DC inverter" because the alternative current (AC) is converted to Direct Current (DC) then, direct current inverted back to Alternative current with desired frequency. As known, the current supplied through the wall outlet has fixed frequency which is 60 Hertz.
Different frequencies supplied to the compressor will result different running speeds of the compressor. Inverter control systems use Pulse Amplitude Modulation (PAM) that is the most advanced and energy efficient method of inverting the current. DC Inverter air conditioners bear special compressors that their speed could be changed by increasing or decreasing the frequency of the supplied power.Therefore, unlike conventional split Air Conditioners/Heat Pumps which cycle between on and off repeatedly, the DC Inverter control system will monitor the room temperature and adjust the compressor speed automatically. Conventional compressors turn on and off to maintain the room temperature at desired level. This will result compressor to draw tremendous energy each time it starts up. This will also reduce the life-span of the compressor and other components that are turning on and off. Once a conventional system is running, it runs at its maximum speed, consuming the maximum amount of energy in order to produce the maximum of cooling or heating to maintain the desired temperature. The system will then cycle between on and off in an effort to maintain this temperature. When a DC Inverter compressor initially starts up, it runs with a higher speed to bring the room temperature to desired level rapidly. Once the set temperature is reached, it slows down and adjust its capacity to counter the heat loss or heat gain of the building. By this way it will maintain a constant temperature.
BASIC OVERVIEW: The indoor unit is hung like a picture frame approximately 6 - 8 feet above the floor usually on an exterior wall. A 2-3 inch hole must be made behind the indoor unit in the exterior wall to run the refrigerant copper tubing, electrical wires and the condensate drain to the outside unit. The indoor unit and outdoor unit are connected to each other by means of refrigerant copper tubing and electrical cables. The condensing unit comes pre-charged with Freon however, the lines still need to be vacuumed to evacuate the excess Nitrogen prior to the final coupling for operation.
Although the installation may seem easy to some, certain tools and experience is necessary to complete installation of a mini split See Installation Tip. 5 Year Compressor - 1 Year on all other Parts Registration card will be sent with unit, this card should be completed by an HVAC technician (installer). Installation of a mini split must be completed by a licensed HVAC (Heating, ventilating, & air conditioning) company to ensure any issues encountered in the future are not due to improper installation / workmanship.Even though mini split setup is below the expertise requirements of central AC systems, these are not "plug-n-play" units that can be properly installed without certain tools any prior HVAC - electrical knowledge. The installation includes electrical, gas, and refrigerant connections and generally regulated by a multiple sets of laws, codes and guidelines, at the federal, state and local levels. The failure to properly install HVAC equipment can raise personal safety and performance concerns. If you receive a damaged or defective product, a replacement unit will be sent out Free of cost. SHIPS TO TO BOTH UNITED STATES AND CANADIAN LOCATIONS! SOMEBODY MUST BE ON SITE TO ACCEPT / SIGN FOR Order. Failure to provide valid contact# will delay order.
25' Lineset kit (1/4 x 5/8). 15' or 25' refrigeration linesets REQUIRED for installation. Mount your condenser at any height on an outdoor sidewall. 16/4 Electrical Wire Harness - For Extending Evap. 3.2 Gallons per Hour Rate - 120 or 220 VAC options.View the Mini Split FAQ >. View the Mini Split Outline Diagram >. The item "1.5 ton 20 SEER 18000 BTU Single Zone Mini Split AC Hyper heat Pump/700 sqft" is in sale since Monday, November 19, 2018.
This item is in the category "Home & Garden\Home Improvement\Heating, Cooling & Air\Central Heating & Cooling Systems\Ductless Mini Split Systems". The seller is "thermospace_acs" and is located in Oak Park, Michigan. This item can be shipped to United States, Canada.